![]() |
Freelance 2016-1 - Printable Version +- (https://bigbluetrains.com) +-- Forum: Branchline (https://bigbluetrains.com/forumdisplay.php?fid=45) +--- Forum: Layouts (https://bigbluetrains.com/forumdisplay.php?fid=46) +--- Thread: Freelance 2016-1 (/showthread.php?tid=7808) |
Re: Freelance 2016-1 - lajry - 01-20-2016 Reinhard Those loads on that bulkhead flat reminded me of steel coil loads. You don't have to have a place that makes or uses them. Like at Santa Fe's Vernon Team use your gantry crane to off load them & fork lift to put them on flatbed trailers. You have a couple of pix of the Vernon crane in your Vernon Flickr pix. Re: Freelance 2016-1 - Catt - 01-20-2016 This is one of the things that I miss being able to do in N and Z.I will definitely be doing this when I do the HO switching layout. :mrgreen: ![]() Re: Freelance 2016-1 - faraway - 01-20-2016 Catt Wrote:This is one of the things that I miss being able to do in N and Z....I am not sure but you know that photo has been taken after the Grassmaster was in action and "before" the vacuum cleaned the mess up? All those fibers are not glued to the layout. Just a small seam left to the track sticks in the glue. This is about the same area after the vacuum clean it up. ![]() The green done this morning is very different from the others because I ran auf of 6mm /1/4" fibers. A first vacuum application made showed the difference very clear. I pulled the plug and made is different by intentionally applying the vacuum at some still not set spots and fill the holes with brown ground cover and some other green. ![]() An overview of the area with the replaced team track and the stub track. Both ending at the right side of the photo now. They spanned up to the left end of the photo. ![]() An other problem are the palm trees. I like them but they limit the theme of the layout a lot. Some small trees are more universal and serve the same purpose. I used small trees I had at hand made for N or Z scale. They had the proportions of oaks etc. with a tall massive stem. I cut the stem and they got the appearance of large shrubs with the branches close to the ground. A form of small trees more often found than the "tiny solitaire". ![]() ![]() ![]() ps. All my palm trees have a nail in the bottom of the stem. They are plugged back on the layout within seconds ![]() Re: Freelance 2016-1 - Catt - 01-20-2016 When I had my last HO layout I had a lumberyard where the track looked almost identical to the picture I reposted.I know I could do that in N using short fibres but there is no way I can do it in Z though I plan to try it . ![]() Re: Freelance 2016-1 - lajry - 01-21-2016 Catt In Z scale a layer of grass color paint would be as tall as Reinhard's HO grass. LOL Re: Freelance 2016-1 - faraway - 01-22-2016 Adding green details. Some of the shrubs on the first and all on the last photo are the residuals found in the shrubs box. ![]() ![]() ![]() Re: Freelance 2016-1 - faraway - 01-23-2016 Got a dozen trees in the mail today. Cut off the stem and drilled a nail in the bottom. It is amazing how little is changed by 12 trees. ![]() ![]() ![]() ![]() ![]() Got the Walthers CP GP9u in the mail too. Plugged the shell on a drive with decoder prepared some years ago for St. Maries River Railroad. Funny thing is that selected drives are not bad at all with a good DCC decoder. The shell is cheap enough to risk a CP project. It is the flexibility of a generic freelance layout I like so much that the palm trees got removed. Re: Freelance 2016-1 - Prairie Trains - 01-23-2016 Looking good, trees always add to a scene regardless of how few or how many are used. Re: Freelance 2016-1 - faraway - 01-30-2016 I am still working on details of the green. One topic is to soften the transitions between green and not green. It was all to straight and technical. ![]() ![]() The other is to take some of the perfection produced with the Grassmaster. ![]() ![]() Re: Freelance 2016-1 - faraway - 01-31-2016 It gets pretty green here and I made up my mind to have the palm trees on the (freelance Florida inspired) layout. ![]() ![]() ![]() ![]() ![]() Re: Freelance 2016-1 - torikoos - 02-04-2016 And all of a sudden, we've moved from more Northern areas to the Southeast again, it almost instantly feels more warm and humid too, now a small section where you can model some Everglades or other swampy bits with a 'gator' in it, and the tone is set :-) (thinking of offshoots of the Florida intracoastal waterway ) Koos Re: Freelance 2016-1 - lajry - 02-04-2016 Really like that there's variations in your grass areas. You could include little trash especially along any roads. It might also include an abandoned car or two. You could also have a public works crew cleaning up the trash or hauling away the cars. Re: Freelance 2016-1 - faraway - 02-04-2016 Here we go. Right under the bridge since about two years. I tried trash but the gators ate it all :o ![]() Re: Freelance 2016-1 - lajry - 02-05-2016 There's too much good stuff left on the front car like windows, headlights & chrome. ![]() Re: Freelance 2016-1 - faraway - 02-09-2016 Andy's fantastic grain elevator made me think if a building made of corrugated steal plates could be made of styrene (evergreen 4527) when the ends of each sheet is elevated a tad (evergreen 104). No rattle can painting today. It is very stormy and it rains cats and dogs at the balcony. ![]() ![]() |