60´Gallows turntable for HOn3
#1
Hi!
This is my new project.
The Model Masterpieces D&RG 60' Gallows turntable in HOn3.

[Image: upload_-1.jpg]

I will, also build the Como Roundhouse to complete the scene.
The drive for the turntable will be a step motor with full indexing. It is a system developed by a friend of mine and very fool proof!
[Smile]

I bought this kit second hand, and it misses the spider gear housing...
I will try to make a new by 3D printing it.

This is a good plan showing how I will do the drive:
[Image: upload_-1.jpg]
(courtesy of Carrie Creek)

I started the build by staining and adding grain to the wood. The stain is Isopropyl alcohol and wiper fluid mixed with vallejo burnt umber and black.

[Image: upload_-1.jpg]

After it dries, I will lightly sand them to remove the fuzz.
More to come soon!
Reply
#2
I've come a little further on the way. The Nut Bolt Washer castings are mostly in place :
[Image: upload_-1.jpg]

[Image: upload_-1.jpg]

I just had to see how my biggest locomotive fits :
[Image: upload_-1.jpg]
Now its time to spike some rails in place.
8-)
Reply
#3
This is looking great so far. Largest loco seems to sit well on the turntable bridge.
It's always nice to see a project progressing so well. Thumbsup Thumbsup Cheers
We always learn far more from our own mistakes, than we will ever learn from another's advice.
The greatest place to live life, is on the sharp leading edge of a learning curve.
Lead me not into temptation.....I can find it myself!
Reply
#4
Looking good ! I love the gallows TT ...they have so much character .
To err is human, to blame it on somebody else shows management potential.
Reply
#5
The weathered wood with the rusty nuts and bolts looks great Applause
Reinhard
Reply
#6
Thanks guys!
Just one more update before bedtime (this is after all Europe, a tad different time zone...Smile )
[Image: upload_-1.jpg]
Filed grooves for the cables.

[Image: upload_-1.jpg]
Soldered the wires to the Code 70 Micro Engineering rails.

[Image: upload_-1.jpg]
The rails spiked and glued!
Big Grin
I use Railway engineering rollee holders.
Reply
#7
The gallow temporarily installed:
[Image: upload_-1.jpg]
Reply
#8
The base is started!
Smile
8 mm plywood base. I've glued the piedestal on the top and a piece of pine underneath. I drilled the holes for the bearings with my pillar drill to get the hole in plumb.
[Image: upload_-1.jpg]

The axle will be replaced with a stainless tube.
[Image: upload_-1.jpg]

The brackets that holds the tie rods are in place.
[Image: upload_-1.jpg]

Had to see how it looks....
[Image: upload_-1.jpg]

The pit wall is to be built using ties. And the pit rail has to be laid. I will use code 40 in the pit..
Reply
#9
Late last night I checked the Turntable and saw that the axle wasn't lining up!?!
That despite using a drill press... probably the bushings tilted a bit when gluing them in at first?
I made a jig, removed the bushings and lined everything up.
[Image: upload_-1.jpg]
Now it is correct!
I've also built the turntable pit wall. I used cork up to the pit ring level.
Then I glued stained ties up to the top.
The ties fit perfectly, I didn't have to trim any of them to fit!
Reply
#10
A small update:
The cork wasn't totally flat for the pit rail, so I mounted a template/scraper on my centre jig. I then spackled the surface and rotated the template to get a flat surface. It worked great!
[Image: upload_-1.jpg]

I made some ties for the pit rail:
[Image: upload_-1.jpg]

I glued them using my jig to get them to point towards the centre.
[Image: upload_-1.jpg]
As you can see in the picture above, I made another template on the jig.
This one were to make the slope in the pit.
I mixed some very soupy plaster which I poured in the pit at the same time as I rotated the template.
After a minute or two, it began to set. I then removed the template (which had a roll of excess plaster on one side).
This is how it looked;
[Image: upload_-1.jpg]

I added some thin paint to prepare for the gravel and sand:
[Image: upload_-1.jpg]

The piedestal was painted as well.
[Image: upload_-1.jpg]
Reply
#11
Oh Man!! That's GREAT!!!! Big Grin Big Grin Big Grin Thumbsup Thumbsup
~~ Mikey KB3VBR (Admin)
~~ NARA Member # 75    
~~ Baldwin Eddystone Unofficial Website

~~ I wonder what that would look like in 1:20.3???
Reply
#12
Really nice work. I like your use of the jig Smile
--
Kevin
Check out my Shapeways creations!
3-d printed items in HO/HOn3 and more!
<!-- m --><a class="postlink" href="https://www.shapeways.com/shops/kevin-s-model-train-detail-parts">https://www.shapeways.com/shops/kevin-s ... tail-parts</a><!-- m -->
Reply
#13
OOOH! Pumpkin pie!
David
Moderato ma non troppo
Perth & Exeter Railway Company
Esquesing & Chinguacousy Radial Railway
In model railroading, there are between six and two hundred ways of performing a given task.
Most modellers can get two of them to work.
Reply
#14
Thanks!
No more pie though... Icon_lol

I have glued the real Colorado gravel in the pit:
[Image: upload_-1.jpg]

[Image: upload_-1.jpg]
I have installed the pit rail as well. Code 40 from Micro Engineering.
Reply
#15
Now it's getting close!
:-)
Mostly done:
[Image: upload_-1.jpg]

[Image: upload_-1.jpg]

[Image: upload_-1.jpg]

[Image: upload_-1.jpg]

The things left to do are to install the ring on top for the tracks and the gear, motor and electric wipers.
8-)
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)