Posts: 992
Threads: 81
Joined: Dec 2008
Hey guys, ...roadbeds...
Usually, yards are flat and you can't make out any difference in height whereas the mainlines are elevated.... usually. Rather than laying cork for each line in the yard, I'm thinking it would seem easier to just lay down one big sheet. Does anybody make sheets of cork for this purpose?
On the flip side, it might be easier to go ahead and lay down the cork for each line and then fill in the in-betweens with wall joint compound.
Thoughts?
Posts: 2,269
Threads: 181
Joined: Dec 2008
Cork sheeting is available at some hobby shops and art supply stores.
Posts: 2,271
Threads: 155
Joined: Dec 2008
You should be able to get sheets of cork at your local big box hardware store. Alternately, you could lay the track right on your subroadbed (plywood, foam, whatever). This approach would give you a height difference between the yard and main, sometimes seen on the prototype so that runaway cars are less likely to enter the mainline "unassisted".
Andrew
Posts: 2,966
Threads: 158
Joined: Dec 2008
TrainNut Wrote:Hey guys, ...roadbeds...
Usually, yards are flat and you can't make out any difference in height whereas the mainlines are elevated.... usually. Rather than laying cork for each line in the yard, I'm thinking it would seem easier to just lay down one big sheet. Does anybody make sheets of cork for this purpose?
On the flip side, it might be easier to go ahead and lay down the cork for each line and then fill in the in-betweens with wall joint compound.
Thoughts?
I have seen it in office supply sotres. It actually comes in a roll shrink-wrapped with plastic.
--
Kevin
Check out my Shapeways creations!
3-d printed items in HO/HOn3 and more!
<!-- m --><a class="postlink" href="https://www.shapeways.com/shops/kevin-s-model-train-detail-parts">https://www.shapeways.com/shops/kevin-s ... tail-parts</a><!-- m -->
Posts: 1,999
Threads: 98
Joined: Dec 2008
Midwest Products makes a corkshee(Walthers #476-3030).Measures 5"w x 113/4"l.
About $9.00 USD.
But..it is probably cheaper at an art supply store. Something to make bullentin boards out of.
Torrington, Ct.
NARA Member #87
I went to my Happy Place, but it was closed for renovations.
Posts: 11,847
Threads: 576
Joined: Nov 2008
I tired the "fill in" approach. A total failure and a real fun thing to clean up and start over again. I actually had everything ballasted before I ruled in favor of starting over again. And yeah, you can probably get sheets of cork at Staple, Office Max or even Hobby Bench.
Don (ezdays) Day
Board administrator and
founder of the CANYON STATE RAILROAD
Posts: 333
Threads: 8
Joined: Mar 2009
I have each line in my yard on subroadbed, should I pull these out, and either lower the tracks to the foam, buy a sheet of cork, or leave it as-is??
-Steven-
The Zealot progress thread: <!-- m --><a class="postlink" href="http://www.zealot.com/forum/showthread.php?t=112267">http://www.zealot.com/forum/showthread.php?t=112267</a><!-- m -->
The current progress thread: <!-- l --><a class="postlink-local" href="http://www.the-gauge.net/forum/viewtopic.php?f=17&t=923">viewtopic.php?f=17&t=923</a><!-- l -->
Posts: 2,271
Threads: 155
Joined: Dec 2008
viperman Wrote:I have each line in my yard on subroadbed, should I pull these out, and either lower the tracks to the foam, buy a sheet of cork, or leave it as-is??
Up to you! But if it's already there (and especially if it's ballasted) and working well, I vote for "leave it".
Andrew
Posts: 333
Threads: 8
Joined: Mar 2009
MasonJar Wrote:viperman Wrote:I have each line in my yard on subroadbed, should I pull these out, and either lower the tracks to the foam, buy a sheet of cork, or leave it as-is??
Up to you! But if it's already there (and especially if it's ballasted) and working well, I vote for "leave it".
Andrew Its there and wired (partially), but not ballasted
-Steven-
The Zealot progress thread: <!-- m --><a class="postlink" href="http://www.zealot.com/forum/showthread.php?t=112267">http://www.zealot.com/forum/showthread.php?t=112267</a><!-- m -->
The current progress thread: <!-- l --><a class="postlink-local" href="http://www.the-gauge.net/forum/viewtopic.php?f=17&t=923">viewtopic.php?f=17&t=923</a><!-- l -->
Posts: 5,859
Threads: 175
Joined: Dec 2008
viperman Wrote:I have each line in my yard on subroadbed, should I pull these out, and either lower the tracks to the foam, buy a sheet of cork, or leave it as-is??
You could leave it as-is, or fill in the low areas with the same material that you used for sub-roadbed. Use joint compound or patching plaster to fill any gaps, and your ballast will cover-up the patch job. Don't use joint compound to fill the low areas, though - applied too thickly it will crack severely as it dries.
Wayne
Posts: 992
Threads: 81
Joined: Dec 2008
doctorwayne Wrote:Don't use joint compound to fill the low areas, though - applied too thickly it will crack severely as it dries.
Wayne
Too bad there's no prototype that resembles severely cracked wall joint compound!
Perhaps if the rail yard has experienced a flood lately, you would see these same type of conditions.
All in good fun!
Posts: 333
Threads: 8
Joined: Mar 2009
Posts: 349
Threads: 25
Joined: Dec 2008
Hi:
We bought sheets of 2' x 4' cork from Home Depot for $16.00. It comes in a roll. We used it on our N-Trak modules in our yard. It is approximately 1/32" thinner than standard N Scale cork roadbed. While it is not significantly lower, it is lower and it was a LOT easier to install when you have 8-10 parallel tracks in a yard area. We painted it a darker brown, laid the track, added ballast, added weeds, and had a good looking yard.
dwight77
Posts: 1,897
Threads: 40
Joined: Dec 2008
Another source would be an auto parts store. They used to sell cork as gasket material. You might need to check a local independent store or a NAPA, I would not be surprised if the big chain diy stores don't bother with gasket material.
Posts: 28
Threads: 8
Joined: Dec 2008
well if you have a old cork board laying around just take it out of the frame and use it it is the same size as road bed. i found 10 of them at the good will for about 2.00 for all . and they where about 24" x 30" so for a nscale layout their is a whole yard in about 2 of them . or you could use the thick card board from a frige, or stove box just glue it down and lay your track and if you wanted to you could use plaster over it to make little mounds of rocks. but you can just balast right on to the card board i did this on a old layout and it look great .
|