Posts: 1,291
Threads: 64
Joined: May 2011
Here's the basic layout for a Palmetto Spur Variation in 7x1 feet. The track is Atlas Code 83 Snap Track with 18 inch Radius Snap Switches. Cheap and easy.
Mike Kieran
Port Able Lines
" If the world were perfect, it wouldn't be " - Yogi Berra.
Posts: 931
Threads: 68
Joined: Dec 2008
Mike - the piccies have gone walk-about
Jack
Posts: 1,291
Threads: 64
Joined: May 2011
Thanks Jack. My bad. I'm uploading pictures while ordering tickets to The Nutcracker. Gets confusing.
Mike Kieran
Port Able Lines
" If the world were perfect, it wouldn't be " - Yogi Berra.
Posts: 931
Threads: 68
Joined: Dec 2008
Posts: 3,262
Threads: 115
Joined: Dec 2008
Mike,Very nice!
Here all these years I thought I was the only one to use snap track and snap switches on small ISLs..
That layout could be built and detailed to the max or one could use the minimalist approach so it could be stored between operation sessions..
Larry
Engineman
Summerset Ry
Make Safety your first thought, Not your last! Safety First!
Posts: 2,269
Threads: 181
Joined: Dec 2008
Mike Kieran Wrote:Thanks Jack. My bad. I'm uploading pictures while ordering tickets to The Nutcracker. Gets confusing. Imagine how the ticket agency feels after receiving your track plans! :?
Posts: 255
Threads: 4
Joined: May 2010
Mike,
I like the layout, but I would avoid the structure along the edge of the layout. If you have the room, I would allow at least 18" of depth and place a road on the edge of the layout followed by a structure and then the major trackage. If you could curve this layout down another wall, I would place a run around track in the design. I don't know much about snap track, but I would do normal trackage if you are going to put the effort into this, but then again thats just me talking.
Larry
Posts: 3,262
Threads: 115
Joined: Dec 2008
Larry,I think that building along the front of the layout makes the layout stand out plus it breaks up a "straight on" view...It shouldn't cause a problem since you can eyeball the car spots.
Larry
Engineman
Summerset Ry
Make Safety your first thought, Not your last! Safety First!
Posts: 1,639
Threads: 87
Joined: Dec 2008
I think I would go wider if I could just so I could add some detailing to the building interiour on that building to show what they do in there.You could always make a outer wall of clesr Lexan or styrene.
Johnathan (Catt) Edwards
"The Ol Furrball"
"I'm old school,I still believe in respect"
Posts: 56
Threads: 0
Joined: Apr 2011
Brakie Wrote:Larry,I think that building along the front of the layout makes the layout stand out plus it breaks up a "straight on" view...It shouldn't cause a problem since you can eyeball the car spots. Hi Larry,
not knowing the height of his up-front building, nor the height of the layout and the way how he envisions (un)coupling i wouldn't be that sure.
With some dedicated car spots the view from the side might be not that good.
Paul
Posts: 3,262
Threads: 115
Joined: Dec 2008
Paul,I still don't see a problem with a building along the front of a ISL..
To my mind that would break up the "oh hum" flat straight on look that ISLs inherit by being flat..
Of course one could use a nonrail served industry but,and IMHO,nothing looks as good as a rail served industry along the front edge.
Larry
Engineman
Summerset Ry
Make Safety your first thought, Not your last! Safety First!
Posts: 56
Threads: 0
Joined: Apr 2011
Larry,
one more time:
when the layout is at armpit level and the building at the front rather high and long, it could be difficult to park a car just before a door and maybe it would not be that easy to uncouple or couple the car.
Without knowing these things i should be a bit careful.
Anyway modelrailroading is about finding the right balance. This balance is for every-one different.
I agree with you, a foreground building or even some trees are wonderful assets.
On the proposed layout I would choose for a shorter building, about 1 foot long, with an additional low (un)loading platform or a teamtrack.
Paul
Posts: 3,262
Threads: 115
Joined: Dec 2008
Paul,I'll split the difference and say a tall building could be a problem.
As far as uncoupling that's no problem..
Use the KD coupler as they were intended to be used-you recall uncouple over the magnet back up to disengage the coupler,then push to spot? That method works quite well even in N Scale.
Larry
Engineman
Summerset Ry
Make Safety your first thought, Not your last! Safety First!
Posts: 255
Threads: 4
Joined: May 2010
Larry,
Just to way in on this discussion, I think that when you look at the plan, there is no need to have the background structures as deep as shown. Why not shallow profile the structures against the wall and actually increase the width of the structure in the foreground? You have one rear structure taking 6 inches of depth and the other three inches. Since there are no tracks leading into the rear structures, depth is not a key element. The edges of the rear buildings will most likely be scenic making their
actual depth hidden. Even if Mike decides to leave the structure on the edge of the layout, it would appear more credible to have a structure with depth in the foreground than against the wall.
If Mike wants to use the 12 width, there is no reason strip wood could not be added down the line to the exterior edge to build out the depth at a later date.
Larry B.
Mike Kieran Wrote:Here's the basic layout for a Palmetto Spur Variation in 7x1 feet. The track is Atlas Code 83 Snap Track with 18 inch Radius Snap Switches. Cheap and easy.
Posts: 3,262
Threads: 115
Joined: Dec 2008
I like the design as is and would indeed narrow the building along the backdrop..I would be tempted to use these buildings from Walthers:
<!-- m --><a class="postlink" href="http://www.walthers.com/exec/productinfo/933-3192">http://www.walthers.com/exec/productinfo/933-3192</a><!-- m -->
<!-- m --><a class="postlink" href="http://www.walthers.com/exec/productinfo/933-3191">http://www.walthers.com/exec/productinfo/933-3191</a><!-- m --> I would add silos for cover hopper or tank car unloading.
For the building on the front of the layout this would be my choice.
<!-- m --><a class="postlink" href="http://www.walthers.com/exec/productinfo/933-3184">http://www.walthers.com/exec/productinfo/933-3184</a><!-- m -->
I have build several foot wide ISLs over the years and I focus more on detailing the narrow buildings I used-these was structure kits cut in half..
I would also add a trailer drop lot and two small nonrail served industries on the right end of the layout.
Larry
Engineman
Summerset Ry
Make Safety your first thought, Not your last! Safety First!
|