Posts: 24
Threads: 8
Joined: Dec 2008
I thought that I should just have my own thread with these question in it then starting up a new thread each time.
So for today....
Where can I buy small steel rod?
The kind that I would poke up through the layout to move the points of my turnout (HO). I looked all over at Home Depot, no luck.
Kent
Posts: 2,959
Threads: 158
Joined: Dec 2008
Look for one of those "K&S" metal/brass displays. If not at your local hobby shop, try Ace Hardware. Music wire is what you need.
--
Kevin
Check out my Shapeways creations!
3-d printed items in HO/HOn3 and more!
<!-- m --><a class="postlink" href="https://www.shapeways.com/shops/kevin-s-model-train-detail-parts">https://www.shapeways.com/shops/kevin-s ... tail-parts</a><!-- m -->
Posts: 453
Threads: 59
Joined: Dec 2008
Hi Kent,
Piano wire (music wire) as suggested works well find a stockist some LHS stock it and take a point with you to get a good fit. any bends do before you cut it to length push through the point hole mark with a permanent pen and use a cut off disc for final lengths.
Posts: 2,271
Threads: 155
Joined: Dec 2008
KentBy Wrote:I thought that I should just have my own thread with these question in it then starting up a new thread each time.
Kent
Hi Kent,
Welcome to Big Blue! (OK, so I'm a bit late on that...
)
Don't be afraid to open a new thread with the question as the topic. Sometimes this is easier (and gets you more responses) than putting all kinds of unrelated questions in a single thread.
Andrew
Posts: 24
Threads: 8
Joined: Dec 2008
MasonJar Wrote:KentBy Wrote:I thought that I should just have my own thread with these question in it then starting up a new thread each time.
Kent
Hi Kent,
Welcome to Big Blue! (OK, so I'm a bit late on that... )
Don't be afraid to open a new thread with the question as the topic. Sometimes this is easier (and gets you more responses) than putting all kinds of unrelated questions in a single thread.
Andrew
Ok Andrew, I'll do it that way.
Thanks
Kent
Posts: 437
Threads: 24
Joined: Dec 2008
Hi Kent.
I have seen it at Ace and Home Depot. Besides piano wire and music wire, I have seen it called spring steel wire.
Loren
I got my first train when I was three,
put a hundred thousand miles on my knees.
Posts: 2,416
Threads: 63
Joined: Dec 2008
Kent: it also helps if you put something more specific than "question" in the subject line.
You can usually find wire even in a hobby shop that doesn't carry trains -- airplanes use it for something.
David
Moderato ma non troppo
Perth & Exeter Railway Company
Esquesing & Chinguacousy Radial Railway
In model railroading, there are between six and two hundred ways of performing a given task.
Most modellers can get two of them to work.
Posts: 605
Threads: 27
Joined: Dec 2008
Does anyone know if guitar strings will work? I grabbed up some that were in the trash at my (former) church.
I only know what I know, and I don't understand very much of it, either.
Member: AEA, American Legion, Lions Club International
Motto: "Essayons"
Posts: 2,458
Threads: 57
Joined: Dec 2008
As I recall, not finding any music wire out here in the boondocks, I ordered some from Walthers. No...guitar strings won't work...
Gus (LC&P).
Posts: 24
Threads: 8
Joined: Dec 2008
Ace didn't have any, but my LHS had lots to choose from.
I kind of felt bad, because I woke up the lady the was behind the counter. No one else was in the store on Saturday afternoon. I bought two different sizes .032 and .055 and it only came to $.74.
She said that I was the first one to come in for the last two hours.
They are a small Mom and Pop operation, I just hope that they can stay in business.
Kent
Posts: 2
Threads: 0
Joined: Mar 2009
Hey Folks,
About piano wire. It is not music wire but check out old/used piano moving places, your local piano tuner is an ally too! Casreful cutting the stuff, it can be nasty and they do sell piano wire cutters. I own such a pair, don't ask. DO USE YOUR GOOD WIRE CUTTERS OR NEEDLENOSE!
Posts: 5,859
Threads: 175
Joined: Dec 2008
A cut-off disc in a Dremel works great for cutting music wire and allows very precise trimming.
For cutting softer wire, such as brass, or, in small diameters, stainless steel, I find that an old #11 blade in an X-Acto works well. Use the "heel" of the blade (to avoid breaking off the tip) and work on a hard surface, such as a sheet of glass. Small diameters can be cut straight through, while larger sizes are best rolled back and forth under the blade.
Wayne
![[Image: up_xm40o.gif]](http://i549.photobucket.com/albums/ii377/upnick/up_xm40o.gif)
![[Image: up_lo-1.gif]](http://i549.photobucket.com/albums/ii377/upnick/up_lo-1.gif)
![[Image: up_turb10k_r.gif]](http://i549.photobucket.com/albums/ii377/upnick/up_turb10k_r.gif)
