Charlie b's layout
(09-08-2025, 11:55 AM)hillyard999 Wrote: Charlie,
Great picture.
that "quarry" scene raises a lot of questions.
how were the stones made so round?  They were hand cut for the most part and I think there was a steam driven lathe for the finish cut  
was there a giant lathe?
I notice all are stacked axis vertical.
It almost looks like they are pulled up from a pit to the left.  They were cut from blocks in the sides of the quarry 
There is the roof to a shed at the right. dynamite storage shed 
The stacked blanks at right seem to be placed on uneven surface.
Likewise the supports for the jib pole mast.

Where is this place?  Workers may be Chinese. It was in East Liverpool and the workers were all local workers 
Very intriguing.

I find an article claiming they were used to grind flint (silica). The quarry was owned by a paper company ad I believe that to be why they would produce mill stones made of sandstone. The flint used by the pottery industry would have to be pure so I can't imagine using sandstone to grind it. 

I came across this article from 1990 that is a better , true version 

 
The mill stones were shipped around the country for use in paper mills to grind wood into pulp.
The International Pulp Stone Co., headquartered in Empire, Ohio, oper­ated the California Hollow quarry at least 20 years, the brothers believe, and closed sometime in the 1920s. Bob Harding was superintendent, and "It was a very high grade of sand­stone - the best the company ever found," Robert Mattern says. "The company only pulled out because they played out the quarry. It got to the place where there ^was too much over­bearing (soil) on, the stone and it was too difficult to remove.'' 

It started with holes drilled in the earth at the top of the quarry. Dyna­mite was placed in the holes, and there would be a shout: "Fire in the hole!" and everybody ran," Robert Mattern remembers.Tons of dirt, blasted loose from the underlying rock, were loaded by steam shovel into wagons. The boys' father would haul the dirt to a spot be­low the present location of the Dres­den Avenue Dairy Queen for dump­ing

I am posting a photo of the page as well as some other pictures that you may find of interest. I hope the page is readable  You can use windows control and the plus key to enlarge. [/align]
                                       
Charlie
Reply
Looks like slicing an appropriate diameter dowel rod is in your future, Charlie! Cool stuff.
Check out my "Rainbows in the Gorge" website: http://morristhemoosetm.wixsite.com/rainbows
Reply
This project looks to be a good one. Can't wait to see it finished. I'm sure it will be superb like the rest of the layout is.
Matt
I can smell a steam post ten blocks away and when I do clear the tracks because the steam express will be hi ballin through
http://cambriaindiana.weebly.com/
Reply
Charlie,
thanks for sharing those great pictures!
and the newspaper article too.

especially like the last photo, showing the lathe & boiler/ belt drive.
interesting that in contrast the derrick/crane was hand cranked.
--Hillyard
Willamette City Belt Line: WCBL
 Virtual Interchange 
Reply
I had a few minutes to work on the quarry tonight.     
Charlie
Reply
That looks Great!!!
~~ Mikey KB3VBR (Admin)
~~ NARA Member # 75    
~~ Baldwin Eddystone Unofficial Website

~~ I wonder what that would look like in 1:20.3???
Reply
Looking great Charlie
Matt
I can smell a steam post ten blocks away and when I do clear the tracks because the steam express will be hi ballin through
http://cambriaindiana.weebly.com/
Reply
I did some more detailing to the quarry and decided to set it in place. I am not going to get too carried away with this but it is a fairly good representation as is.  I have plans to ballast the loading track  and I have LPBs that need painted to make it look like it is really functioning.     
Charlie













ch
Reply
Very cool! Looking forward to the finished scene!
Check out my "Rainbows in the Gorge" website: http://morristhemoosetm.wixsite.com/rainbows
Reply
(09-29-2025, 05:59 PM)TMo Wrote: Very cool!  Looking forward to the finished scene!

The few details it will get are going to be tough because it is the only area on the layout that is a tough stretch to reach 
Charlie
Reply
Charlie, I have some tough areas to reach so I bought an overhead creeper it is a very handy thing for me, and the harbor fright ones are nit pricey.
Jim
Reply


Forum Jump:


Users browsing this thread: 8 Guest(s)